How To Change Battery In Htc 10

HTC 10 DIY Teardown for screen, charging port, battery replacement

Past alina | May 12th, 2016 | | 18

Have you lot got the New HTC ten in your hand? Unconsciously broke the screen? Accidents do happen. The official cost for replacing the HTC 10 screen is upward to 140 USD and the bargain time is around 7-10 business days which is quite long and expensive. If y'all desire to salvage money and TAT, DIY repair would be your choice. Today we're going to teardown this controversial smart phone to see how difficult it is to repair it by yourself?

Tools needed:

Guitar pick
Phillips screwdriver
T5 Torx screwdriver
Metallic opening spudger
Tweezers
Slim playing cards

‍‍Step one Ability off the phone‍‍

Always power off the phone and take out the SIM & SD carte du jour tray before disassembling.

1take out sim&sd card tray.jpg

Step 2 Detach the screen

Estrus upwards the LCD screen edges to melt the adhesives, then insert the playing menu and slide along the edges to cutting the LCD screen adhesives (Notation: don't slide too deep into the bottom left side, considering at that place is a flex cable), hither y'all may need to warm up the screen edges repeatedly.

3.insert playing card.jpg

4 warm screen edges up repeatedly.jpg

5 cut adhesives.jpg

Afterward loosening adhesives, you lot tin can pry upwardly the LCD screen.

6 open lcd screen.jpg

7 pry up lcd screen.jpg

Step 3 Disassemble the middle plate

Don't think you tin can remove the screen right at present, 12 screws are there waiting!

8 undo 12 screws.jpg

Pry up and remove the heart plate with LCD screen assembly from the rear housing now.

10 pry up middle plate.jpg

11seperate lcd with middle plate.jpg

Pace 4 Remove loudspeaker

By the manner, we can remove the loudspeaker since the rear housing is right in front of the states. Undo the spiral and y'all can pry it up.

12 undo 1 screw.jpg

13.pry up loudspeaker.jpg

Step v Remove the LCD screen

Moving to the forepart housing associates, still the HTC-style, looks complicated within with so many adhesive tapes!

Remove ii screws property the bombardment first before pulling out the battery connector.

14 disconnect battery flex.jpg

Then pull out the charge port flex connect to the main board and peel off the tape covering the LCD screen and digitizer flex cable, you can disconnect the betoken cable now.

15disconnect charge port flex.jpg

16 peel off tapes.jpg

17 disconnect the signal cable.jpg

Disconnect the LCD screen flex cable connector.

18 Disconnect the LCD screen flex cable.jpg

Pry upwards the whole LCD screen and digitizer flex cable and put it down through the slot, now we're washed with separating the LCD touch on screen from the centre plate assembly.

19 Pry up the whole LCD screen and digitizer flex cable.jpg

20 separating the LCD touch screen from the middle plate assembly..jpg

Left the eye plate assembly now.

21middle plate assembly .jpg

Stride vi Remove charging port flex cable.

Disengage the ii T5 Torx screws property the charging port flex.

22 Undo the 2 T5 Torx screws .jpg

Disconnect the charging port connector.

23 Disconnect the charging port connector..jpg

Disconnect the 2 betoken cable connectors then.

24 Disconnect the 2 signal cable connectors..jpg

And ane more than screw in the corner.

25 Undo one more screw in the corner..jpg

So go dorsum and forth to pull off the touch on push button pads.

26 pull off the touch button pads. .jpg

At present pry upward charging port flex cable very carefully and slowly.

‍Step seven Remove master board with rear photographic camera

Peel off the xanthous and blackness tape roofing the connectors.‍

28 Peel off the yellow and black tape .jpg

Release two connectors.

Also practice the same to the other side after releasing i indicate cable connector here.

Undo 2 screws on the primary board.

32 Undo 2 screws on the main board.jpg

Pry up the master lath with the rear facing photographic camera at present.

Be Conscientious! The vibrate motor is soldered to the chief lath. Remove it together.

Step 8 Remove the other logic board

Undo 3 screws offset.

Remove forepart facing camera covering by the protective tape.

Thought of removing the logic lath at present. Oops, the battery covered the flex cable underneath.

Need to take out the battery first, prepare for the strong adhesive underneath battery.

Now loosen cables adhered to the middle plate. Then the logic board tin can exist removed finally.

Left the middle plate with the ear speaker now.

Afterward the whole teardown, do you have any thoughts for this so HTC-styled HTC 10? If you are interested in fixing your phone past DIY work, Etrade Supply will provide you the about cost-effective replacements and repair tools. Whatever bug and ideas, leave a comment below to share with us!

(Motion-picture show source: how2tech)